Isuzu G-series Twin Cam

The Ebay kits were purchased from M D Spares. A guy bought him out of stock (which I assume was the guy on Ebay) but they just ordered more in and currently have 10 in stock @ $350 a set. M.D. Spares Pty Ltd 4 Horscroft Place Moorabbin Victoria 3189 Australia Phone: +61 3 9553 0388 Fax: +61 3 9555 2...

Are there any available for sale? I would like to get a set for myself.



Cheers, Ben

Question for you guys. I have 2 G200 twin cams. 1 the 117 type with the upwards facing oil filter and the non ratcheting tensioner and 1 with the downwards downwards facing oil filter and the ratcheting style tensioner. Are the timing covers interchangeable? I would like to put the timing cover with...

Poida wrote:If possible, can we get hold of a copy of any diagrams anyone happens to come across, especially if it has been translated.

I have sent you an email with the translated pdf attached.

Hey guys, quick question. I got the factory wiring diagram translated and it mentions an input from a vehicle speed sensor. Did any of either our Piazza's or Gemini's come with this fitted. I am assuming some sort of load sensor and it is like the o2 sensor which is optional and is just the for bett...

Could the third one be a thermo switch for the Electric fans? Especially if it was off a track car. The two i have only have 2 sensors on it, as stated by someone earlier, its has a pin type like on the under side of a standard gemini inlet for the temp gauge, and a two pin with the same sort of plu...

bosch part numbers for the distributor are Rotor Button, bosch no:GH605 came from a honda accord 1.6litre 79-83 civic 79-80 prelude 1.6litre nissan 78-82 pulsar Distributor Cap,Bosch no:GH604 came off a mid 76 to late 77 nissan 180b 78-82 pulsar 1.3 or 1.5litre 74-78 honda accord (cvcc) civic 1500 ...

Hi I am after a dizzy cap for this distributor. does anyone have one or a part no?

Thanks

Ben

Well i have found that there are a few differences between my wiring and the Gemini manual. They are: 1. I have nothing in the connector for pins 16 & 31 which i assume is an o2 sensor they are there on the computer just no wires connecting to them. 2. I have no idea what the connector second fr...

I was told by my mate that its not for cooling but heating (can be seen in pic four). I have some pics of my motor. from what i can tell Its is a bit of a bitsa. It looks like a 117 motor , Itec Manifold (Also have 117 forward facing) and an ECGI computer. http://img153.imageshack.us/img153/9256/gem...

I realize that but I need to have it looking stock for registration and hoses hanging off with bolts in them (as it is now) does not look factory. which one is the vac line for the brake booster??
Thanks Ben

Ok now that the motor runs i need to work out the plumbing properly Does anyone have any close pics of the inlet manifold with vac lines attached? I haven't been able to find any clear ones of complete motors also where does the water come from for the throttle body?

Thanks

Ben

Thanks for the replies. I have now had the motor running so I know the computers is fine. I will put it in with the computer as is for rego then swap to an aftermarket ecu and keep the factory one in a padded cell tucked away just in case it is needed again in the future.

No probs thanks for the reply. How do people get them registered without standard computers?? once i get it going i will pull the loom down and get a pinout to post up here incase anyone else needs to know.

Does anyone know what the wire colors for the injectors on the itec injection? I have a piazza JR130 computer anyone know the pinouts? i have the loom its just it was off the motor when i got it and wanna put it on properly first time.

Thanks

Ben